Fumeclear® FC-1002A Fume Extractor Instructions for use

Product Overview                               

*This product conforms to applicable CE requirements and the purifying effect has been confirmed by the American PONY international professional testing agency.

*This product has double ports and double tubes.

Usage scenarios of this product:

  • This product is suitable for applications where fumes are produced such as smoke, peculiar smells, dust, poisonous and harmful gas, soldering, laser marking & carving, printing, and medical care, etc.

  • With the triple-filter design and powerful suction, the absorbing efficiency and filtration ratio can reach 99.97%. The purified air can be discharged directly indoors.

FC-1002A filtration system consists of:

Our products package with 7 filter

  • Pre-filter*5 365*175*25mm
  • Medium hepa filter*1 365*175*55mm
  • Main carbon filter*1 385*195*250mm

Filter Use & Maintenance 

This product uses disposable filtering elements. When these elements have been use to a certain extent, they need to be cleaned or replaced in order to guarantee the good purifying effect of the machine.

1. Pre-filter

Use method: Place the Pre-filter on top of Middle Filter. The front side (rough side) is facing upwards (air inlet direction). When the accumulated dust on the Pre-filter is over 70% and cannot be cleaned any more, please replace the Pre-filter with a new one.

2. Middle Filter

Use method: With the handle side facing up, put the Middle Filter inside the Main Filter. The medium filter shall be immediately cleaned off when the accumulated dust on the Middle Filter evidently affects the suction power. When it cannot be cleaned any more, please replace the Middle Filter with a new one.

3. Main Filter

Use method: With the handle side facing up, place the Main Filter at the bottom inside the machine. When it cannot effectively eliminate the peculiar smell in the smoke, please replace it with a new one.

Specifications

Model FC-1002A
Air inlet interface Φ75mm *2 flange
Voltage  AC 110/220V
Power 210W
Max. No-load Speed(r/min) 6000
Negative Pressure 3000Pa
Filtering effect 0.3μm99.97%
Noise <65dB
CFM 194
Dimensions(L*W*H) 425*250*410mm
Weight 15Kg

 

Accessories included

Name of Parts

Qty

Specification

Remarks
Motor 1 Installed
Power Line 1 1.5M 10A250V
Duct 1 75mm dia*1.4m
Warranty card 1
User Manual 1
Pre-Filter 5 1of 5 is installed
Medium filter 1 Installed
Carbon Filter 1 Installed

 

Check Before Using

Before switching on the power for the first time, please ensure that the following conditions exist, so as to guarantee safe operation.

  1. The machine should beintact;
  2. The power switch should be in theOFF position;  
  3. The filter element(s) should beevenly placed;
  4. The cover and box body should beinstalled securely;

The speed-regulating button is adjusted to “OFF” Status;  

Safety Precautions

  • Before use, please read and follow the safety precautions below to prevent fire and personal injury.  
  • This product is prohibited to be used in a high temperature environment (above 80℃) or in a flammable, explosive or greasy environment.
  • Supply wire must be grounded during operation.Internal electric voltage of the product is as high as 310V.
  • Do not remove or install filter elements while the machine is operating. Hands or other objects should not touch the rotating impeller.

 

Installation & Use instructions

  • Filtering Core Installation

Open the top cover and correctly install the high-efficient filtering core, medium-efficient filtering core, primary-efficient cotton filtering with top cover and press for buckle hasps at the two sides.

  • Suction Duct Hose Installation
  1. Removethe hose from the package, and attach it to the duct flange on the cover of the machine.
  1. Turn the tube, aim exhaust fume collecting hood with the smoke outlet. Adjust the suction distance based on the application.

⚠️When adjusting the direction of suction duct hose, try to maintain a broad loop or bend radius of the hose, otherwise it will affect the suction force. The suction inlet shall directly face the working point. Keep the distance within 150mm.

⚠️Try to avoid areas with excessive air flow, otherwise suction force will be affected or diminish completely.